Group Relamp

Energy efficient t5, t8 and fluorescent relamp lighting projects

T5, T8, & Fluorescent Group Relamp

Some of our lamps out, they don’t seem to be as bright as when we first converted and other fixtures don't work at all.

ROI Energy provides what’s referred to as a “Group Relamp Project”. This is where we typically come in after hours and replace ALL the T5 or T8 lamps in your fixtures. 

  • This can be for fluorescent high bay fixtures in a manufacturing company or warehouse.
  • It can also be done for office 2x2’ and 2x4’ recessed ceiling mounted troffer fixtures.
  • Weekends and “off-shifts” are a good time to do this work so we don’t interrupt your production.
  • Since we buy thousands of lamps and ballasts direct from the manufacturers, we have excellent prices on quality brand products.

All lamps have an average rated lamp life based on hours of operation. When your lamps begin to reach their “end of life cycle” they begin to diminish in lumen (light) output or just go out.  It becomes unproductive to try to replace these just a few at a time, especially when there are hundreds or thousands of lamps in a facility.

ROI Energy is extremely competitive when it comes to group relamp projects.  While we are at it, this is the time to replace any ballasts which are no longer working.  You’ll notice night lights which may be on 24X7, tend to have ballasts out due to their “always on” status.

We install Philips or GE long life lamps and GE ballasts.  Our lamps are high quality, long life lamps, typically rated at 36,000 hours so you don’t have to relamp as often. Defective ballasts typically are determined after we replace the lamps and the lamps don’t illuminate.


Give us a call when you are ready for a quotation to provide this service. In the case of high bay fixtures, we include scissors and articulating lifts, along with labor in our cost for this service. 330-931-3905


Group Relamping: Replacing all lamps at once

Replacing all lamps in a space at the same time, even though most haven’t burned out, often provides multiple benefits

At many facilities, when a lamp burns out, all the following steps are taken as part of spot relamping. A technician determines the lamp type, possibly by a visit to the site, gets a lamp, carries a ladder to the site, opens the fixture, replaces the lamps and then arranges for disposal.

The entire process may well distract employees near the lamp. And without close oversight, the last step is often truncated by simply dropping the lamps into the nearest dumpster where they are quickly covered — and probably smashed — by other trash, releasing their mercury. The labor involved in this process may be a significant hidden cost, especially when compared to alternatives.

Most lamp manufacturers and lighting maintenance firms recommend changing lamps before they burn out, with good reason. While perhaps a bit counterintuitive, doing so greatly reduces labor wasted on spot relamping, reduces workplace disruption and better controls lamp disposal. Lamps are replaced en masse (usually during off hours) as they approach about 60 to 70 percent of their rated lives, which is when roughly 10 percent may have burned out and before failure rates begin to climb.

Such group relamping is often done by crews whose main focus and experience is time-efficient fixture maintenance because they are paid on a piece rate basis. Trained in proper lamp disposal, they take responsibility for off-siting and documenting removed lamps.


Group relamping that follows a written work specification will also ensure the following worthwhile tasks are performed:
  • Check for broken or damaged lampholders. One reason for lighting failure often missed during spot relamping is a cracked lampholder or socket that could lead to a smoking fixture if a short circuit results.
  • Replace failed ballasts. Spot relampers may not be equipped or have access to inventory for replacing failed ballasts.
  • Reduce on-site lamp and ballast inventories. Lighting maintenance firms maintain their own stock of lamps and ballasts, obviating the need for a customer to maintain more than odd lamps used in only a few fixtures.
  • Recycle lamps.
  • Handle difficult locations. Professionals may be better equipped for high bay or difficult access areas, such as over operating equipment.

How Often?

While lamp lives vary, group relamping cycles for linear fluorescent lamps are often spaced about four to five years apart. Group relamping may be sequenced floor-by-floor, or done for an entire building, as desired to accommodate operations, crew size, etc. Lamps are gathered and disposed of in large groups, simplifying compliance with environmental regulations — which, for mercury, are becoming tighter.


Better Lamps, Better Output

When relamping, we will install name brand lamps and ballasts. We always use high lumen lamps which are typically rated for 36,000 hours, which means you won’t have to relamp as often.

 

Lighting Retrofits

Lighting retrofits pay for themselves, adding to your bottom line. Many manufacturers & warehouses still use outdated lighting. Converting to LED or T5 high bay fixtures can save 50%-70% on your lighting energy cost and provides more light!

Energy Savings

We'll provide your payback analysis & explain how an LED or T5 high lighting retrofit could save your business 50% or more on your electric bill. This savings translates to company profits! Get a risk-free energy analysis today.

How It Works

The savings from your electric bill pays for your lighting upgrade. We work around your schedule so we don't interrupt production. Upper management won't spend an hour or two on this entire cost reduction initiative when you work with ROI Energy.

No-Risk Energy Analysis

ROI Energy will conduct a risk-free energy analysis to determine your savings potential . Get started today by submitting this form to find out how much you could save. As owner of ROI Energy, I promise you won't be disappointed. ~ Bob Taussig
Back to Top